Honda S2000 Torque Specs w/Socket Sizes

[Soviet]

I've decided to create a master list of torque specs that I can reference while working on the car. All torque specs are in ft-lbs unless specified. If you have a correction or a suggestion please PM me.

BRAKES

Front Brakes
Brake Caliper Bracket Bolts (17mm) - 79.6 (AP1) 83.2 (AP2)
Brake Caliper Guide Pin Bolts (12mm) - 24

DRIVETRAIN

Transmission
Transmission Bellhousing Bolts (17mm) - 47
Transmission Bellhousing Bolts (14mm) - 33
Transmission Drain Plug (3/8") - 29
Transmission Fill Plug (17mm) - 33
Transmission Mount (14mm) - 28
Transmission Output Shaft Locknut (27mm) - 119
Clutch Slave Cylinder to Transmission Bolts (12mm) - 16
Clutch Slave Cylinder Banjo Bolt - 22
Clutch Master Cylinder Mounting Nuts (12mm) - 9.4

Propeller Shaft
Propeller Shaft Bolts (Allen, 6 per side) - 24 (AP1) 36 (AP2)

Driveshafts / Axles
Rear Axle To Differential (14mm) - 61
Rear Axle Nut (36mm) - 150-180 + 60 degrees (Billman Spec)

Differential
Differential Bearing Cap Bolts - 33
Differential Breather Plate - 11
Differential Case (10 bolts) - 19
Differential Drain Plug (24mm) - 33
Differential Fill Plug (23mm) - 33
Differential Mounting Bracket Bolts (19mm) - 47
Differential Mounting Bracket Nuts (19mm) - 55
Front/Rear Differential Mount Nuts (19mm) - 47
Front/Rear Differential Mount Bolts (14mm) - 33

INTERIOR

Seat Rail Front (12mm) - 16
Seat Rail Rear (14mm) - 22

POWERTRAIN

Cooling System
Radiator Fan Bolts (10mm) - 5
Radiator Fan Switch (24mm) - 17
Radiator Stay Bolts (10mm) - 8.7

Exhaust System
Catalytic Converter to Header Nuts (12mm) - 16
Exhaust to Catalytic Converter Nuts (14mm) - 25
Primary Oxygen Sensor - 16
Secondary Oxygen Sensor - 33

Engine
Oil Baffle Plate (10mm) - 8.7
Oil Drain Plug (17mm) - 29
Oil Filter - 16
Oil Jets - 12
Oil Pan Bolts(10mm) - 8.7

SUBFRAME

Front Subframe
Engine Mount Stiffer / Front Tie Bar Nuts/Bolts (14mm) - 28
Subframe Bolts (19mm/17mm) - 43 (rear most), 84 (two forward most)

SUSPENSION

Front Suspension
Upper Control Arm to Chassis Bolt (17mm) - 75.9
Lower Control Arm to Damper Bolt (17mm) - 47
Damper Top Nut (14mm) - 36
Upper Ball Joint Castle Nut (17mm) - Ap1: 36-43 AP2: 41-48
Lower Ball Joint Castle Nut - AP1: 43-51 AP2: 51-58
Lower Ball Joint Bolt (17mm) - 47
Tie Rod End Nut (19mm) - 40
Caster Bolt (17mm) - 58
Camber Bolt (17mm) - 58
Swaybar Endlink Nut (14mm) - 28
Brake Line to Damper (12mm) - 16
Engine Mount Stiffer / Front Tie Bar Nuts/Bolts (14mm) 28
Wheel Speed Sensor Bolts (10mm) - 7.2

Rear Suspension
Upper Control Arm to Chassis Bolt (17mm) - 97.6
Lower Control Arm to Damper Bolt (17mm) - 47
Damper Top Nut (14mm) - 36
Upper Ball Joint Castle Nut (17mm) - Ap1: 36-43 AP2: 41-48
Lower Ball Joint Castle Nut - 51-58
Trailing Arm Castle Nut - 36-43
Suspension Stiffener (aka tie bar) (14mm) - 33
Swaybar Bushing Bolt (14mm) - 40
Swaybar Endlink nut (14mm) - 28

[andrewhake]

Great idea! Thank you very much. Going to sticky this so it stays at the top. Really appreciate you taking the time to do this, it is this type of stuff that really helps a site be useful and grow.

If anyone has suggestions of other major bolt specs to add please mention it here.

[JamesD89]

Thanks for putting this together; gonna print it out and tape it to my toolbox.

[BlueBottle]

Very nice !

Maybe add the rear hub in there?

[Soviet]

Very nice !

Maybe add the rear hub in there?

Good point!